Introduction to Solar Energy
The sun's energy arrives on earth in the primary form of heat and light. Other aspects of solar radiation are
less easily perceived and their detection often requires sophisticated equipment. All solar radiation travels
through space in waves, and it is the length of these waves (the shortest is less than a millionth of an inch, the
longest more than a thousand yards) by which all solar radiation is classified. The aggregate of all radiation
aspects of the sun is called the solar spectrum.
There are two important facets about the solar spectrum.
1. While the sun emits radiation in all wavelengths, it is the short wavelength radiation that accounts for the
majority of energy in the solar spectrum. For example, the portion of the spectrum perceived as the visible light
is a relatively small segment compared to the variety of spectrum wavelengths, yet accounts for 46 percent of
the energy radiating from the sun. Another 49 percent, that which is perceived as heat, is derived from the
infrared band of the spectrum.
2. The proportion of different wavelengths in the solar spectrum does not change and therefore the energy
output of the sun remains constant. A measurement of this phenomena is known as the Solar Constant,
defined as the amount of heat energy delivered by solar radiation to a square foot of material set perpendicular
to the sun’s rays for one hour at the outer edge of the earth’s atmosphere. The Solar Constant measurement
is about 429.2 BTU’s with minimal changes over the year. The energy measured as the Solar Constant is not a
measure of the amount of solar energy that actually reaches the earth’s surface, since as much as 35 percent
of all the solar radiation intercepted by the earth and its surrounding atmosphere is reflected back into space.
Additionally, water vapor and atmospheric gases absorb another 15 percent. As a global average only about
35-40 percent of the solar radiation entering the atmosphere actually reaches the earth’s surface.
As a practical matter, global averages are of little interest. The essential point is that the atmosphere impacts
on the amount of solar energy that actually reaches the earth’s surface - the more atmosphere solar radiation
has to move through, the more is lost on the way. In this regard, two celestial events – the daily rotation of the
earth and its seasonal tilt of the earth's axis – are important in determining the length of atmosphere through
which the sun’s rays must pass before striking any particular location on the globe (Fig. 1).
The amount of solar energy reaching the earth's surface is determined by the amount of atmosphere through
which it must pass.
These events set the upper limit amount of solar energy that can reach the surface of the earth at any location
on any day of the year.
One of the conditions for accurately measuring the Solar Constant requires the intercepting surface to be
perpendicular to the sun’s rays. Since solar radiation travels in parallel rays, the perpendicular position
identifies the maximum density of rays striking a surface. Any deviation from perpendicular reduces the
radiation density and the amount of energy intercepted. This is best illustrated in Fig. 2.
Figure 2. These illustrations demonstrate how energy density is determined by the angle of incidence. The
amount of light emitted by the flashlight is the same in both illustrations but it is spread over a larger area (right)
when the light is tilted away from its original perpendicular position (left).
The angle created by incoming radiation and a line perpendicular to an intercepting surface is called the angle
of incidence. Table 1 illustrates that a fairly large increase in the angle of incidence results in only a modest
reduction in intercepted radiation.
RADIATION AND SURFACES
When sunlight strikes a surface it is reflected, transmitted or absorbed, in any combination depending on the
texture, color and clarity of the surface. All completely opaque surfaces both reflect and absorb radiation but
do so in different ways. For example, a rough surface such as stucco reflects sunlight in a scattered fashion
while a smooth, glossy surface reflects uniformly and at an angle equal to the angle of incidence. The
wavelengths of solar radiation that are reflected are determined by the color of the surface material. A red
stucco surface, for example, will scatter (diffuse) wavelengths in the red band of the spectrum and absorb all
others (Fig. 3), while a white glossy surface will reflect all wavelengths in the visible spectrum at an angle equal
and opposite to the angle of incidence.
Figure 3. Color is perceived when visible light is reflected from a surface. Red surfaces reflect red wavelengths
and absorb all others.
Conversely, a rough black surface absorbs all wavelengths in the visible spectrum, while the transparent
surface of window glass allows nearly all radiation to pass through it with comparatively little reflection or
absorption, and without deflecting it from its parallel lines of travel. Translucent materials also transmit
radiation but scatter the rays as they pass. It should be noted that relatively few materials are excellent
reflectors, transmitters, or absorbers of the sun’s rays.
Sunlight, in the form of short wave solar radiation, exhibits a transformation from solar energy to heat energy
when impacting a material (absorption). The temperatures of a white surface and a black surface exposed the
same direct sunlight is a simple demonstration of this conversion. The temperature of the black surface is
higher because it is absorbing more solar energy. As solar energy is absorbed at the surface of a material it
stimulates movement of the molecules in the material. Molecular movement is measured in terms of heat – the
greater the movement, the greater the heat. Since the color black absorbs more of the spectrum than the color
white, it will in turn be hotter (more molecular excitement) than white.
As a material absorbs radiation and molecular movement continues to accelerate, the heat energy is
redistributed through the material due to the natural phenomenon of maintaining equilibrium. This occurs when
stimulated molecules, vibrating at a faster rate, impact adjacent molecules vibrating at a slower rate, thereby
dissipating and "spreading the wealth". In this way, heat is conducted away from the source of energy as the
material seeks to distribute the energy evenly throughout its mass. The rate at which energy flows or is
conducted though a material depends on the density of the material and conduction, the rate at which
molecules are capable of receiving and passing on energy. Gases are poor conductors; metals are
comparatively good conductors; and less dense materials containing tiny air pockets and voids conduct heat at
a much slower rate.
Heat transfer from a solid material to a fluid medium (liquid or air) occurs by radiation (infrared). It is a
continuation distributed molecular "bumping" between a solid material and a transfer medium (air or liquid). The
added dimension of using fluids is they can move across a hot solid surface, allowing molecules of the fluid to
become agitated (heat), then move away from the heat source, and t be replaced by new, unheated
molecules. This process of fluid movement is called natural convection when the movement is unaided by
machinery (i.e. hot air rises), and forced convection if the process is aided by a pump or fan.
The process occurs naturally as the molecules of a fluid begin to vibrate when heat is applied, and then
becomes less dense (lighter) than the surrounding unheated fluid. The lighter heated molecules rise at a rate
determined by the amount of heat applied. Boiling water is a good example of heated molecules near the
burner rising quickly to the surface to the point of surface disruption (boiling). Steam generated by the process
is simply water molecules whose vibration rate is violent enough to allow them to break from of the water
Birds that seem to hang in the air without beating their wings are evidence of the power of natural convection.
On clear sunny mornings, air at the surface of the ground (especially dark surfaces) is heated rapidly and rises
in columns with enough force to suspend the bird overhead and even push it upward. The reverse of this
process occurs as convected molecules get further from the heat source of heat, give up their energy (slower
molecular excitement), and fall. Conduction and convection can be thought of as processes by which solar
energy can be both transported and stored.
The principle of solar energy absorption was discussed in terms of two surfaces exposed to the sun.
Conduction was then discussed to show how absorbed solar energy moves through a material, always in a
direction away from the source of heat to attain equilibrium. NOTE: Any molecular movement is continually
generating heat in the form of radiant energy. Unlike solar energy, radiant energy is limited to infrared
radiation emitted from a material at low temperatures. The extent to which a material emits thermal energy
depends both on the temperature of the material and nature of its surface. Polished metal surfaces are poor
emitters and poor absorbers of thermal energy. Again, as with solar radiation, the amount of thermal energy a
surface will intercept depends on the angle of the incoming radiation.
Glass has the special characteristic of transmitting nearly all solar radiation that it intercepts (which moves
through it) and is less transparent to most thermal radiation. The temperature build-up in a closed car on a
sunny but cold day is evidence of this characteristic. Solar energy passes through the windows is absorbed by
interior materials, and reradiated into the interior space in the form of thermal energy (heat) which is unable to
pass back through the glass to the outside. This has become known as the greenhouse effect.
All materials can store heat to some degree. The ability of a material to do so is called its specific heat – the
amount of heat, measured in BTU’s for a given mass, a material can hold when its temperature is raised one
degree Fahrenheit. As an indicator of a material's value as a heat storage medium in solar heating of spaces,
the specific heat of a material is not very useful. The usefulness of a material in such an application is
determined by its heat capacity, a measurement of the specific heat of a material multiplied by its density. The
higher the heat capacity, the more effective the material is for heating and cooling.
Finally, a good storage medium material must absorb heat when it is available, and give I t up when it is
needed, and it must be a relatively good heat conductor. In Table 1 the comparative specific heat and heat
capacity measurements for a variety of materials is given, and it shows there is no perfect storage medium in
terms of volume, storage capacity, and conductivity.
Published by Rodale Press, Inc., 1980. A project of Western SUN Arizona and Western Solar Utilization
Intro to Solar Energy